If you find that there is a second nut underneath the wing nut that is also frozen, repeat the same trick again. The wing nut should loosen, and can be removed. Use a wrench to turn the nut in the tightening direction, and use a pliers and turn the wing nut in the loosening direction. It only needs to be finger-tight, as it will tighten as we go. Thread one nut onto the bolt, leaving enough thread for the washer and another nut. Take two nuts and a washer out of the kit. Presumably, you have already bought a set of new bolts to replace the corroded ones. I would like to suggest a third option below.
However, the wing nuts on the tank bolts are so corroded, they’re stuck. Be prepared, some water may still leak from the ballcock.So you have a leaking toilet and want to remove the tank from the bowl to fix it. Some of them can be removed by hand, others may require a small wrench or channel lock pliers. Once you have made sure that the tank is completely empty, you can proceed and disconnect the water supply line. To do this, you can go ahead and shut off the toilet water supply valve, flush the toilet and then use a sponge to get the rest of the water left in the tank. Before you do that, it is a good idea to completely empty it. This repair involves completely removing the toilet tank. STEP 2: SHUT OFF THE TOILET SUPPLY VALVE, FLUSH THE TOILET & EMPTY THE TANK Once you have determined that the leak is, in fact, coming from the tank bolts, you can go ahead and get a Toilet Tank/Bowl kit. Take your time, as this step is necessary to determine what tools or parts you need to fix it. Leaks from the bottom or the main water connection should be easier to spot, however, if you look closely between the tank and the bowl, you should also be able to see or feel the water in between the two.
As I said before, there are a few places where a toilet can leak. STEP 1: INSPECT THE AREA AND DETERMINE WHERE THE WATER IS COMING FROMīefore I was able to determine that the toilet was leaking from the tank bolts, I had to inspect it.
#How do i remove toilet tank bolts that are stuck how to
HOW TO FIX A TOILET LEAKING FROM THE TANK BOLTSīefore you start, make sure you have all the parts and tools you need to complete the repair, which are not many, then proceed with step 1. The next two are the ones I show you on this post. Slip the open end onto the nut, hold the light gray piece from rotating while tightening the black screw that drives the cutter into the nut. After tapping off that section of the nut, you should be able to pry the nut off with a chisel or unscrew it with locking pliers. If not, drill more holes between the two you just drilled. If the leak is on the main water connection, you may need to inspect the connection hose as well as the water supply inlet/ballcock, and replace as necessary. Back off the black bolt which pulls the cutter back into the 'handle'. Remove the bit and drill another hole 60 to 90 degrees away, then tap the section between the holes with a chisel, and the nut should separate. However, the first one requires removing the toilet and replacing the wax seal, so it takes more time than any of the others. There are a few places where a toilet can leak:Īll of them are easy fixes.
Fortunately, leaky toilets, especially if they are leaking from the tank bolts, are an easy fix. A water leak, no matter how small, can be a homeowner’s worst nightmare, it not only has the potential to cause extensive damage to your home, but it can also cause some health and safety issues.Īs soon as I noticed the leak, I got on it. When it comes to water leaks, I do my best to get things fixed as soon as possible. It was not the first time I had to deal with one either, it is part of being a homeowner. Unfortunately, though, I had to deal with one leaky toilet tank a few days ago. It is one of the reasons why renters enjoy being renters and the most common argument against land lording you read about on the Internet. Fixing a toilet is perhaps the last thing a homeowner wants to deal with.
0 kommentar(er)
